Knoxville Epoxy Floor Pros applies polyaspartic floor coatings across Knoxville, TN for homeowners and businesses who can't give up a garage, shop or patio for most of a week. Polyaspartic cures in hours instead of days, stays clear in direct sun and can go down in weather that would stall a standard epoxy. Polyaspartic jobs we handle can include:
So far this year our crews have finished 52 polyaspartic floors, from a covered patio in Concord to a church fellowship hall in Norwood. Because the coating sets so quickly, every batch is mixed in small kits on site and rolled out within its working window by installers who do this system week in and week out.
Polyaspartic systems usually cost $6 to $10 per sq ft, and most garages are walk-on ready in about 4 hours with cars parking inside the next day.

A Ball Camp homeowner needed their two-and-a-half car garage back the same night because both cars couldn't sit in the driveway during a work week. We ground the 620 sq ft slab at 7 a.m., broadcast a gray and black flake into the base and rolled the polyaspartic topcoat by early afternoon.
The family walked on it by 4 p.m. and parked inside the next morning.
Cost: $4,650 for 620 sq ft
Timeframe: 1 day

A pool deck in Choto had an old acrylic coating that had faded, chalked and started peeling after a few summers of full sun. Our crew stripped it, repaired the cracked control joints and laid a tan polyaspartic system with a fine quartz texture so bare feet don't slip.
The deck was dry and back in use two days later, and the color hasn't faded since.
Cost: $8,100 for 900 sq ft
Timeframe: 2 days

A motorcycle shop in Lonsdale had a service bay and showroom floor stained with oil and brake fluid that never fully came clean. We ground out the stains, filled the cracks and rolled a dark gray base under a clear polyaspartic topcoat that wipes clean after every oil change.
The work ran Saturday and Sunday, and bikes were rolling through the bay again Monday morning.
Cost: $12,000 for 1,500 sq ft
Timeframe: 2 days
POLYASPARTIC SYSTEMS WE INSTALL

01 · POLYASPARTIC SYSTEM
Speed is the reason most people pick polyaspartic, but that speed only pays off when the slab is ready for it. The crew grinds to a CSP 2 or 3 profile, fills cracks with a fast-set polyurea and checks moisture before a single kit is opened.
Each batch has to be rolled out in about 15 minutes, so two installers work side by side to keep a wet edge. Thin coats go down one after another, which keeps lap marks and trapped bubbles out of the finished floor.
02 · POLYASPARTIC SYSTEM
Most garage jobs around Knoxville start and finish on the same day, a big relief for families who park inside every night. A full flake broadcast hides tire marks and small slab flaws, while a solid color suits anyone after a cleaner workshop look.
Hot tire pickup is the usual worry with cheap garage paint kits. A polyaspartic topcoat holds up to warm tires rolling in off Pellissippi Parkway in July, and road salt rinses off with a garden hose once winter comes around.


03 · POLYASPARTIC SYSTEM
Sunlight is hard on standard epoxy, which tends to yellow and chalk on porches, pool decks and patios. Polyaspartic is aliphatic, so it keeps its color outdoors and can carry a fine quartz texture that gives bare feet some grip near the water.
Businesses lean on the fast cure in a different way. A small shop, salon or showroom floor can be coated after closing on a Friday, and Knoxville Epoxy Floor Pros has it ready for customers again by Monday morning.
04 · POLYASPARTIC SYSTEM
A finished basement should not mean a week of fumes and furniture stacked in the garage. Polyaspartic goes down with very little odor, and the whole system cures fast enough that most basements are walkable by the same evening.
Every slab gets a moisture reading before anything is mixed, since basement concrete in Knox County often pulls dampness from the soil. When the numbers run high, a vapor barrier primer goes down first so the coating stays bonded for good.


05 · POLYASPARTIC SYSTEM
Pairing a polyaspartic base with a full flake broadcast gives a garage or workshop that textured granite look along with serious durability. The chips hide dust and small chips in the concrete, while the clear polyaspartic topcoat locks everything in.
Flake blends can be matched to cabinets, trim or a shop color, and the chip size changes how busy the floor looks. Knoxville Epoxy Floor Pros leaves a sample board in your chosen blend before the install date so there are no surprises.
06 · POLYASPARTIC SYSTEM
An older epoxy or flake floor that has gone dull does not always need to be torn out. When the original coating is still well bonded, the crew screens the surface, repairs any chipped spots and rolls on a fresh polyaspartic topcoat.
A recoat brings back the gloss and adds UV protection that keeps the floor from yellowing near the garage door. Most recoats are finished in a single day, and light foot traffic can start that evening.

WHY HOMEOWNERS AND BUSINESSES CHOOSE US
01
Each kit is mixed only when the crew is ready to roll it, so nothing starts curing in the bucket.
02
Polyaspartic can go down in near-freezing temperatures, so winter jobs don't have to wait until spring.
03
Every slab is tested and the readings are written on your quote, since fast-curing coatings don't forgive damp concrete.
04
A crew lead tests surface hardness before giving the okay to drive on it, instead of guessing by the clock.
05
Every residential garage system carries a written limited warranty that specifically covers hot-tire pickup.
06
The person who measures your floor works on the crew that grinds it, so the same faces stay from the first visit to the final walkthrough.

Light foot traffic is usually fine after about 4 hours. Cars can park inside after 24 hours, and a cold or humid day may stretch that a little longer.
It depends on the space. Polyaspartic cures faster and won't yellow in sunlight, while epoxy gives more working time and often costs less on indoor floors that never see UV light.
Yes. It holds its color in direct sun, so it works well on porches, patios and pool decks. A fine quartz texture is usually added outdoors so wet feet don't slip.
Yes. Polyaspartic can cure in temperatures close to freezing, so winter installs are common here. The slab still has to be dry, which is why moisture gets checked before any work starts.
Not when the floor has been ground and coated properly. Hot tire pickup usually comes from thin paint kits rolled over unprepped concrete, which is why every slab gets diamond ground first.
Sweep or dust mop to clear away grit, then wash with a pH-neutral soap and a soft mop. Skip citrus and vinegar cleaners, and rinse road salt off in winter before it dries on the surface.

WHAT HAPPENS AFTER YOU CALL
01 Free on-site estimate
Usually booked within 2 business days of your call.
02 Itemized written quote
Grinding, repairs, materials and labor are listed line by line.
03 Quick start dates
Most installs begin within 2 weeks of signing.
04 Furniture moving and cleanup
Both included, so the space is ready to use when the crew leaves.
05 Local to East Tennessee
Serving Knox, Blount, Anderson and Loudon counties.
Get a FREE Quote
Rated #1 Epoxy Floor Installer in Knoxville, 2026