Knoxville Epoxy Floor Pros installs flake epoxy flooring across Knoxville, TN for garages, basements, shops and kennels that need a tough floor with a little personality. Colored vinyl chips are broadcast into a wet base coat and sealed under a clear topcoat, which hides dust and tire marks while adding a light, grippy texture. Flake floors we install can include:
So far this year our crews have finished 63 flake floors, from a two-car garage in Gibbs to a dog grooming shop in Inskip. Before ordering chips, a small panel coated in your blend is left at the house so you can see the colors in your own light.
Flake floors typically cost $5 to $9 per sq ft, and most residential jobs are finished in 1 to 2 days.
A Holston Hills homeowner had a two-car garage with spalled concrete from years of winter road salt dripping off the cars. We ground the slab, rebuilt the worst spalls with epoxy mortar and broadcast a gray, black and white granite blend to full coverage under a polyaspartic topcoat.
The family parked back inside three days later, and the salt stains haven't come back.
Cost: $3,120 for 480 sq ft
Timeframe: 2 days

A basement in Westmoreland held a laundry room and home gym on bare concrete that always felt damp and dusty. Our crew tested the slab, rolled on a moisture vapor barrier and laid a mocha and tan flake blend that hides lint, chalk and the odd dropped weight.
The washer and dryer went back on the second evening, and the gym was in use by the weekend.
Cost: $7,200 for 900 sq ft
Timeframe: 3 days

A dog boarding facility in Heiskell needed kennel runs that could take daily hose-downs and harsh disinfectants without soaking into the concrete. We installed a medium flake epoxy with 6 inch coved bases along every wall and a gritty topcoat so wet paws and staff boots stay planted.
Runs were finished in two groups, so the dogs always had a dry side to stay in.
Cost: $13,600 for 1,600 sq ft
Timeframe: 4 days

FLAKE SYSTEMS WE INSTALL

01 · FLAKE SYSTEM
A flake garage floor starts with a diamond-ground slab, because chips and resin only stay put on concrete that has been opened up. Cracks get filled and the moisture reading is logged before a tinted base coat goes down wet enough to grab every chip.
Once the base cures, loose flakes are scraped and vacuumed off before the clear topcoat seals everything in. That scraping step is what keeps the floor from feeling sharp under bare feet or socks.

02 · FLAKE SYSTEM
Full broadcast means chips are thrown until no base color shows through, giving a dense, speckled look close to terrazzo. It also hides hairline cracks, patched spots and old stains far better than any solid color can.
Most Knoxville homeowners land on a blend of three or four colors from the 30+ options on the sample ring. That extra layer of chips adds a bit of thickness, so the floor shrugs off dropped tools and jack stands.

03 · FLAKE SYSTEM
Basements get a moisture test before anything else, and slabs that read high get a vapor barrier primer under the flake system. A partial broadcast over a light base keeps a lower level bright without making it feel like a garage.
Kennels, grooming shops and small retail floors like the way chips hide hair, dust and scuffs between cleanings. Knoxville Epoxy Floor Pros can also run a coved base up the walls in wet areas so the whole room hoses down clean.

04 · FLAKE SYSTEM
The topcoat is what decides how long a flake floor keeps its color and shine. A clear polyaspartic finish cures fast, resists hot-tire pickup and will not yellow when sunlight pours in through an open garage door.
Most homeowners pick a satin or gloss sheen, and a fine grit can be mixed into the final coat for better grip when the floor gets wet. That extra layer also makes oil drips and road salt easy to wipe up.

05 · FLAKE SYSTEM
Outdoor concrete needs a system that can handle UV, rain and summer heat without fading or turning slick. Knoxville Epoxy Floor Pros uses a UV-stable polyaspartic base and topcoat outside, with a lighter flake blend that stays cooler underfoot.
Screened porches, back patios and pool surrounds all get a textured finish so bare feet stay steady around water. Most outdoor flake jobs wrap up in a single day when the weather cooperates.

06 · FLAKE SYSTEM
Flake comes in more than 30 stock blends, from soft grays to bold reds and blues, and chips can be mixed to match cabinets, trim or a company color. Chip size changes the look too, with larger flakes reading busier and smaller ones looking closer to granite.
A sample board is made in your blend and left with you before the install, so you can check it in your own space at different times of day. Partial broadcast and full broadcast options are shown side by side at the same visit.
WHY HOMEOWNERS CHOOSE US
01
A small board coated in your chosen blend is left behind for a few days, so the colors can be judged under your own lights before chips are ordered.
02
Every floor is scraped and vacuumed after the broadcast cures, which knocks off the sharp edges that make cheap flake floors rough underfoot.
03
Each slab gets a reading before the quote is final, and basements with high numbers get a vapor barrier primer instead of a gamble.
04
Garages that catch sun through an open door get a UV-stable polyaspartic clear coat, while busy shops can step up to a thicker urethane finish.
05
Every residential garage system carries a written limited warranty that specifically covers hot-tire pickup.
06
The person who measures your floor works on the crew that grinds it, so the same faces stay from the first visit to the final walkthrough.
Most garages and basements are finished in 1 to 2 days. Foot traffic is fine the next day, and cars can usually park inside after about 72 hours.
Yes, as long as the slab is tested for moisture first. Basements with high readings get a vapor barrier primer, and the flake texture hides the small dips and patches older slabs tend to have.
Partial coverage scatters chips over a solid base color, so some of that base shows between flakes. Full coverage buries the base completely, which looks more like terrazzo and adds extra thickness.
Yes. Chips can be mixed from more than 30 colors, and a sample panel of the blend is left at the house so you can see it in your own light before the order goes in.
Flake adds a light texture, so it grips better than smooth epoxy. For floors that get wet often, a fine grit can be mixed into the topcoat for extra traction.
Sweep or dust mop often, then wash with warm water and a pH-neutral cleaner. A squeegee pulls water out of the chip texture quickly, and harsh citrus or acidic cleaners are best avoided.

WHAT HAPPENS AFTER YOU CALL
01 Free on-site estimate
Usually booked within 2 business days of your call.
02 Itemized written quote
Grinding, repairs, materials and labor are listed line by line.
03 Quick start dates
Most installs begin within 2 weeks of signing.
04 Furniture moving and cleanup
Both included, so the space is ready to use when the crew leaves.
05 Local to East Tennessee
Serving Knox, Blount, Anderson and Loudon counties.
Get a FREE Quote
Rated #1 Epoxy Floor Installer in Knoxville, 2026