Epoxy Floor Repair in Knoxville, TN | Professional Coating Repairs

Knoxville Epoxy Floor Pros has handled epoxy floor repair on 72 failing floors that someone else installed, from peeling garage coatings off Emory Road to a gift shop floor in Pigeon Forge worn through by summer foot traffic. Most failures trace back to thin product, skipped grinding or moisture coming up through the slab, and each of those needs a different fix.


  • Common problems: hot tire pickup, bubbling from outgassing, peeling at the edges and chips around joints
  • Diagnosis: adhesion pull tests and an ASTM F1869 calcium chloride moisture test show why the coating let go
  • Price range: spot repairs start around $350, while full grind-and-recoat jobs run $3 to $6 per sq ft
  • Timing: most repairs take 1 to 2 days, with foot traffic after 24 hours


Homeowners along Asheville Highway and in Vestal usually call once a few chips turn into a peeling strip down the middle of the garage. A quick look tells whether a patch will blend in or the whole floor needs to come up, and that answer comes in writing before any grinder is turned on.

Recent Epoxy Floor Repair Projects by Knoxville Epoxy Floor Pros

  • Peeling Garage Floor Repair in Kimberlin Heights
  • Chipped Epoxy Repair at a Townsend Outfitter
  • Delaminated Plant Floor Repair in Kingston
Peeling Garage Floor Repair in Kimberlin Heights

A homeowner in Kimberlin Heights had a big-box store epoxy kit lifting in sheets under both car tires after just two summers. We ground off the failed coating from 480 sq ft, ran a moisture test that came back clean and installed a 100% solids epoxy base with a polyaspartic topcoat that resists hot tire pickup.


The cars were parked back inside on day three, on a floor rated for hot tires straight off the highway.


Cost: $2,880 for 480 sq ft

Timeframe: 3 days

Chipped Epoxy Repair at a Townsend Outfitter

An outfitter shop in Townsend had dozens of chips and gouges where kayaks and gear carts had been dragged across a 10-year-old epoxy floor. Knoxville Epoxy Floor Pros cut out the damaged spots, filled them with epoxy mortar, then sanded the whole 1,400 sq ft and rolled on a fresh color coat and topcoat.


Work was done on two weekdays before the spring paddling season, so the shop never lost a busy weekend.


Cost: $5,600 for 1,400 sq ft

Timeframe: 2 days

Delaminated Plant Floor Repair in Kingston

A parts plant in Kingston had epoxy delaminating across a 2,200 sq ft packing area where water seeped up through an old slab with no vapor barrier. The crew shot-blasted down to sound concrete, applied a moisture vapor barrier primer and rebuilt the floor with a high-build epoxy and a urethane topcoat.


The packing line moved to a neighboring bay for the week, so shipments still went out on schedule.


Cost: $13,200 for 2,200 sq ft

Timeframe: 4 days

REPAIR SERVICES WE OFFER

Epoxy Floor Repair Services in Knoxville, TN

01 · REPAIR SERVICE

Peeling, Bubbling, Blistering, and Delaminating Epoxy Coating Repair

Peeling usually starts at a garage door edge or under tire paths, while bubbles point to moisture or outgassing from the slab. Finding the cause comes first, because a patch over a wet slab will lift again within a season.


Loose coating is ground off until the edges are firmly bonded. A moisture barrier primer goes down where needed, then the new layers are feathered into the sound areas.

02 · REPAIR SERVICE

Cracked, Chipped, Pitted, and Worn Epoxy Floor Coating Repair

Small chips from dropped tools and cracks along control joints are the most common calls. Each damaged spot is cut back to a clean edge and filled with epoxy mortar or a flexible polyurea joint filler.


Worn traffic lanes get a light sanding and a fresh topcoat over the whole floor, so the repair blends in. Flakes and color are matched as closely as the original allows.

03 · REPAIR SERVICE

Commercial and Industrial Epoxy Floor Repair

Forklift ruts, chemical burns and failed coatings around drains can shut down part of a shop if they spread. Repairs are scheduled in sections, often on nights or weekends, so production keeps moving.


Fast-cure repair mortars let traffic back on damaged areas within hours. When a floor is failing across most of its area, a full grind and recoat usually costs less than chasing patches.

04 · REPAIR SERVICE

Epoxy Floor Recoating and Topcoat Renewal

A floor that has lost its shine or picked up scuffs and light stains often just needs a new topcoat. When the base layers are still well bonded, the surface is screened, cleaned and finished with a fresh urethane or polyaspartic coat.


Recoating costs far less than a full replacement and is usually done in a single day. It also resets the clock on wear, so a busy garage or shop floor can go years before it needs attention again.

05 · REPAIR SERVICE

Concrete Joint and Spall Repair

Control joints and spalled edges are where most coatings start to break down, especially under forklifts or car tires. Damaged joints are cut clean and refilled with a semi-rigid polyurea that flexes with the slab instead of cracking.


Spalled spots get rebuilt with epoxy mortar and ground flush before any color goes back on top. The repaired areas are blended into the existing floor, so the fix is hard to pick out once the coating cures.

06 · REPAIR SERVICE

Moisture Damage Repair and Vapor Barrier Systems

Moisture pushing up through the slab is one of the top reasons coatings bubble and lift, and patching over it only buys a few months. The failed coating comes off, the slab is tested with in-slab RH probes and a moisture-tolerant epoxy primer goes down first.


Knoxville Epoxy Floor Pros then rebuilds the floor on top of that barrier, so the new system stays bonded even in damp basements and older garages. The test readings are shared with you before any work is quoted.

WHY OWNERS TRUST US WITH REPAIRS

Why Choose Knoxville Epoxy Floor Pros for Epoxy Floor Repair in Knoxville, TN?

Fixing someone else’s floor takes a bit of detective work, and a few habits keep repairs from failing a second time.

01

Cause found before the quote

Pull tests and moisture readings explain why the coating failed, so the fix targets the real problem.

02

Patch or recoat, explained plainly

Photos of the damage come with a written note on whether a spot repair or a full recoat makes more sense.

03

Color matching on site

Small test patches are mixed and checked against the old floor in daylight before the repair is finished.

04

Repairs backed in writing

Repaired areas carry the same written warranty terms as a brand new install.

05

ICRI-certified moisture testing

A crew lead certified as an ICRI Concrete Slab Moisture Testing Technician checks every slab before a coating system is chosen.

06

Same crew, start to finish

The person who measures your floor works on the crew that grinds it, so the same faces stay from the first visit to the final walkthrough.

Epoxy Floor Repair FAQs in Knoxville, TN


Can peeling epoxy be fixed without redoing the whole floor?

Sometimes. If the peeling is limited to one area and the rest of the coating passes a pull test, that section can be ground out and patched. Widespread peeling usually means a full recoat.

Why is my epoxy floor bubbling?

Bubbles usually come from moisture vapor or air escaping the concrete while the coating cured. A moisture test shows which one, and a vapor barrier primer solves most cases.

Will a repaired spot match the rest of my epoxy floor?

Close, but rarely perfect on an older floor that has faded. A fresh topcoat across the whole surface is the best way to make repairs disappear.

How much does epoxy floor repair cost in Knoxville?

Spot repairs start around $350, and full grind-and-recoat jobs run about $3 to $6 per sq ft depending on how much coating has to come off.

Does Knoxville Epoxy Floor Pros repair floors installed by other companies?

Yes, most repair calls are for floors someone else put down. The first step is figuring out what product was used and why it failed.

WHAT HAPPENS AFTER YOU CALL

What to Expect From Our Crew

01 Free on-site estimate

Usually booked within 2 business days of your call.

02 Itemized written quote

Grinding, repairs, materials and labor are listed line by line.

03 Quick start dates

Most installs begin within 2 weeks of signing.

04 Furniture moving and cleanup

Both included, so the space is ready to use when the crew leaves.

05 Local to East Tennessee

Serving Knox, Blount, Anderson and Loudon counties.

Get a FREE Quote

Rated #1 Epoxy Floor Installer in Knoxville, 2026