Knoxville Epoxy Floor Pros has coated 38 slippery floors with anti-slip epoxy flooring across Knox and Blount counties, from car wash bays on Chapman Highway to a dental office in Farragut. Most calls come after a near miss on wet concrete, and the fix usually takes less time than people expect.
Before any resin is mixed, a free sample board with three grit levels comes along to the walkthrough so the floor can be tested in real work shoes. Property managers in Fountain City and Halls have used those boards to settle the debate with staff in about five minutes.
A small brewery in Bearden had a sealed concrete floor that turned slick every time a keg line dripped or a server spilled a pitcher. We ground 2,400 sq ft of taproom and brewhouse floor, built cove base around the drains and broadcast aluminum oxide into a gray epoxy body coat before sealing it with a chemical-resistant topcoat.
The brewhouse side was finished first while the taproom stayed open, so the doors were only closed for two weekdays.
Cost: $19,200 for 2,400 sq ft
Timeframe: 4 days

A private gym in Powell kept seeing members slip on the tiled locker room floor right outside the showers. Knoxville Epoxy Floor Pros pulled up the cracked tile, patched the slab and installed 1,600 sq ft of quartz-broadcast epoxy with a fine grit that stays comfortable under bare feet.
The showers and locker rows were split into two phases, so members always had one side to use.
Cost: $13,600 for 1,600 sq ft
Timeframe: 3 days

A metal fabrication shop in Alcoa had a sloped loading ramp and a coolant-soaked production floor where forklifts and staff kept losing traction. The crew degreased and shot-blasted 3,800 sq ft, then laid a coarse aluminum oxide texture on the ramp and a medium grit across the shop floor.
Work ran over a long weekend and two night shifts, so production never fully stopped.
Cost: $34,200 for 3,800 sq ft
Timeframe: 5 days

ANTI-SLIP SYSTEMS WE INSTALL

01 · ANTI-SLIP SYSTEM
Grip comes from what sits inside the coating, so the crew picks aluminum oxide for greasy floors and rounded quartz where people walk barefoot or in socks. That choice gets made after a look at how the space is cleaned and what spills on it most.
Prep starts with diamond grinding and crack repair. A primer, body coat and broadcast follow, and the topcoat is rolled thin enough to leave the texture exposed.

02 · ANTI-SLIP SYSTEM
Kitchens, locker rooms, ramps and entryways all get wet in different ways, which is why one texture rarely suits a whole building. Entry mats usually stop at the door, while the coating keeps working across the rest of the floor.
Owners who mop daily tend to like a medium grit that still cleans up with a deck brush. Heavier texture is saved for ramps and wash-down zones where grip matters more than looks.

03 · ANTI-SLIP SYSTEM
A textured coat is only as good as the slab under it, which is why Knoxville Epoxy Floor Pros starts every job at the grinder. Old sealers, oil stains and laitance all come off before any resin touches the floor.
Moisture gets checked with a calcium chloride test, and spalled spots are filled with epoxy mortar. That way the grit sits evenly instead of pooling in low areas and leaving bald patches where feet land.

04 · ANTI-SLIP SYSTEM
Sloped surfaces are where a smooth floor turns dangerous, especially once rain, coolant or forklift tires get involved. Ramps, stair treads and dock plates get a coarse aluminum oxide texture that holds up to heavy traffic and still gives boots something to grab.
Contrasting safety yellow can be added to stair nosings and ramp edges so the change in level is easy to spot. Most ramp and dock work is scheduled over a weekend so deliveries keep moving during the week.

05 · ANTI-SLIP SYSTEM
Grease and water on a kitchen floor make for a bad mix, and a busy cook line is no place to lose your footing. These floors get a quartz-filled system with a textured topcoat that stays grippy through nightly degreasing and hot water washdowns.
An integral cove base runs up the wall so mop water never gets trapped at the edges, which also helps during health inspections. The texture is set fine enough that the floor still squeegees clean at closing.

06 · ANTI-SLIP SYSTEM
Pool decks and patios stay wet for hours, and bare feet need more grip than shoes do. A UV-stable polyaspartic system with a rounded quartz texture gives traction without feeling rough on toes or scraping knees.
Lighter colors help keep the surface cooler during East Tennessee summers, and the coating seals out chlorine and pool chemicals. Knoxville Epoxy Floor Pros can usually finish a pool deck in one or two days, so the backyard is ready for the weekend.
WHY SAFETY-MINDED OWNERS CHOOSE US
Traction is the whole point of this kind of floor, and a few habits set the work apart from a standard coating job.
01
A tribometer reading is taken after cure, and the numbers go into the closeout packet for your insurer.
02
Three texture levels are mixed on small panels so staff can step on them in work shoes before anyone picks one.
03
Resin runs a few inches up the wall in wet rooms, which keeps water from sneaking under the edge.
04
High-traffic lanes wear smooth over the years, and a thin textured recoat can be added in a single evening.
05
A crew lead certified as an ICRI Concrete Slab Moisture Testing Technician checks every slab before a coating system is chosen.
06
Every coating system carries a written limited warranty against peeling and delamination.
Most projects land between $5 and $11 per sq ft. Heavy grinding, cove base and coarse aggregate push the number up, while a clean slab with a medium grit keeps it closer to the low end.
A medium grit cleans up fine with a deck brush and a squeegee. Very coarse textures do better with an auto scrubber, so the texture is matched to how the floor actually gets cleaned.
Often yes, as long as the old coat is still bonded. It gets sanded, cleaned and checked for adhesion, and anything loose is ground off before the new textured layer goes down.
Standard epoxy yellows in the sun, so outdoor ramps and patios get a UV-stable topcoat over the textured base. Slope and drainage matter too, since standing water lowers grip on any surface.
Light foot traffic is usually fine after 24 hours, while carts and forklifts wait about 72 hours. A cold slab in winter can stretch that by a day.
Yes, on commercial jobs a DCOF reading is taken once the floor cures. The result goes into the closeout paperwork, which helps when an insurer or inspector asks for proof.

WHAT HAPPENS AFTER YOU CALL
01 Free on-site estimate
Usually booked within 2 business days of your call.
02 Itemized written quote
Grinding, repairs, materials and labor are listed line by line.
03 Quick start dates
Most installs begin within 2 weeks of signing.
04 Furniture moving and cleanup
Both included, so the space is ready to use when the crew leaves.
05 Local to East Tennessee
Serving Knox, Blount, Anderson and Loudon counties.
Get a FREE Quote
Rated #1 Epoxy Floor Installer in Knoxville, 2026